I am super excited that we are having a baby girl in about 2 months time...so much so that I am making her bedding. First is the crib skirt. I used a couple of great blogs to get started. They were http://dkhibler.blogspot.com/2009/06/crib-skirt-tutorial.html and Leanne Barlow's Elle Apparel http://elleapparel.blogspot.com/2012/05/crib-bedding-101.html.
I found some great fabric at babybedding.com called white pagoda. I ended up buying something like 4 or 5 yards of the white pagoda because I am making multiple items from this fabric. It is also important to note that this fabric had a picture on it so I had to be careful to cut it so the picture was vertical as it should be.
To assemble I used Leanne Barlow's measurements and added 3 inches to the long side making it 55" x 15.25" so that I could add one large pleat to the skirt. It ended up not mattering in my case though as the crib rail covered it up completely!
I also decided to go ahead and cut 2 long pieces. Most the time it wouldn't really matter as you only see the front of the crib, but if I decide to sell the set later, I didn't want there to be a problem.
Long Sides (2) 55" x 15.25" which allows .25" seam allowance
Short Sides (2) 27" x 15/25" with .25" s.a.
Center section of white muslin 28" x 15.5" with .25" s.a.
I always iron the seams to make sewing easier...especially when sewing a pleat.
I then sewed together.
Tada! I think the skirt turned out super cute!
Thursday, November 15, 2012
Crib skirt
Labels:
baby,
baby girl,
crib dust ruffle,
crib skirt,
DIY,
sew
Thursday, January 12, 2012
From Placemat to Accent Pillow...
We have recently been redoing the downstairs living room. I found some great wing-back side chairs, and I wanted new pillows to go with them. After looking around a bit though, I just couldn't find anything I wanted. I really wanted them to be washable because that area gets a lot of through traffic, and I also wanted them to add some color and look nice without spending too much. Finally, I didn't want to have to sew both pillows myself since my sewing skills are not exactly top of the line...not to mention I didn't have the time.
So, I had a set of place mats from Target already on hand, and I bought a white accent pillow and zipper from Hobby Lobby.
I placed the place mat around the pillow, marking the width, and cut a little over one inch off the width making sure to leave enough material to sew with. I wanted the pillow to be small and long.
I turned the pillow inside out and got ready to pin the zipper. This is the hard part. To make the seam look 'more' professional, fold the cut material length down so that the right side of the material is facing up along the open seam. Place the zipper along the right side of the material so that the folded seam lies on the zipper and pin it in place. You should have three layers to pin...the zipper, the folded seam, and the pillow side. Also note the more material you allow in the seam, the more you will hide the zipper when it is finished. The zipper will have a "lip" of material to cover it up. I did not give my first pillow a large lip as you can see, but the second I tried it and liked it a lot better.

Sew along the pinned line.
Line up the back side of the zipper making sure both sides of the zipper are even.
And repeat.
To finish it off, I actually sewed in a slight diagonal from the end of the zipper up towards the corner of the pillow. If you sew it straight out the zipper will protrude from the pillow, so this technique will help hide it. And lastly, the place mats had a small thread line around the edge, making it almost look like it had piping, so I finished the corners off with the same.
Here it is, zipper side up!
All in all, I am really happy with my new pillows. Most will never know they used to be place mats, and the best part is they are washable! I haven't taken a picture of them on my new chairs yet, but when I do I will post it. It took me about an hour each after gathering all the materials, but a good seamstress could do it in half the time.
So, I had a set of place mats from Target already on hand, and I bought a white accent pillow and zipper from Hobby Lobby.
I placed the place mat around the pillow, marking the width, and cut a little over one inch off the width making sure to leave enough material to sew with. I wanted the pillow to be small and long.
I turned the pillow inside out and got ready to pin the zipper. This is the hard part. To make the seam look 'more' professional, fold the cut material length down so that the right side of the material is facing up along the open seam. Place the zipper along the right side of the material so that the folded seam lies on the zipper and pin it in place. You should have three layers to pin...the zipper, the folded seam, and the pillow side. Also note the more material you allow in the seam, the more you will hide the zipper when it is finished. The zipper will have a "lip" of material to cover it up. I did not give my first pillow a large lip as you can see, but the second I tried it and liked it a lot better.
Sew along the pinned line.
Line up the back side of the zipper making sure both sides of the zipper are even.
And repeat.
To finish it off, I actually sewed in a slight diagonal from the end of the zipper up towards the corner of the pillow. If you sew it straight out the zipper will protrude from the pillow, so this technique will help hide it. And lastly, the place mats had a small thread line around the edge, making it almost look like it had piping, so I finished the corners off with the same.
Here it is, zipper side up!
All in all, I am really happy with my new pillows. Most will never know they used to be place mats, and the best part is they are washable! I haven't taken a picture of them on my new chairs yet, but when I do I will post it. It took me about an hour each after gathering all the materials, but a good seamstress could do it in half the time.
Subscribe to:
Posts (Atom)